In short: Sixteen 40HQ containers of DN630 HDPE dredging pipe, matched pipe floats and DN630 rubber delivery hoses have been manufactured, pressure-tested and delivered to a marine contractor in Malé, Maldives. The shipment supports an island reclamation and harbour maintenance programme in the Indian Ocean, where saltwater corrosion, tidal access and limited crane capacity make lightweight HDPE the preferred pipeline material.
The complete order was loaded in 16 * 40HQ containers within 28 days of purchase order confirmation, with third-party inspection completed before vessel departure.

| Item | Specification | Quantity | Loading |
|---|---|---|---|
| HDPE dredging pipe | PE100, DN630, SDR17, 12 m segments, butt-fusion ready | 276 segments (approx. 3,312 m) | 11 * 40HQ |
| HDPE pipe floats | PU-foam filled, HDPE shell, DN630 clamp, stainless steel hardware | 260 pairs | 4 * 40HQ |
| Rubber dredge hose | DN630, steel-wire reinforced, 10 bar working pressure, flanged | 300 m (25 * 12 m) | 1 * 40HQ |
| Parameter | Value |
|---|---|
| Outside diameter | 630 mm |
| Wall thickness | 37.4 mm (SDR17) |
| Material | PE100 / PE100-RC, UV stabilised |
| Nominal pressure | 1.0 MPa (water, 20 °C) |
| Ring stiffness | SN8 (≥ 8 kN/m²) |
| Standard length | 12 m per segment |
| Jointing method | Butt fusion (hot plate) |
| Design service life | 50 years in buried and marine conditions |
DN630 refers to a nominal outside diameter of 630 mm. In dredging service this size is the standard discharge line for medium cutter suction dredgers and booster stations, balancing flow capacity against the buoyancy required from the float train.



Malé presents specific constraints that shaped the loading plan. Containers were packed in reverse installation order, so the first pipe out of the container matched the first section of the discharge line. Pipe segments were nested with timber saddles to prevent ovality during ocean transit, and float sets were shipped fully assembled to avoid on-site bolting at the quayside. Discharge at Malé commercial harbour is tide-dependent, so the delivery schedule allowed a buffer window for barge transfer to the reclamation area.

DN630 is the nominal outside diameter in millimetres. For a SDR17 pipe this corresponds to a 37.4 mm wall and a 1.0 MPa pressure rating.
Approximately 300 metres, or 25 segments of 12 m, depending on wall thickness and whether saddles or end caps are included.
Float buoyancy is calculated from the submerged weight of the pipe, the slurry inside it and the hose assembly. For DN630 SDR17, one float pair per 12 m segment is the typical configuration.
This 16-container shipment is part of an ongoing programme supplying HDPE dredging pipelines, floats and rubber hoses to island and coastal contractors across the Indian Ocean. Project-specific pipe diameters, float buoyancy and hose pressure ratings can be engineered against the dredger specification before production begins.
In short: Sixteen 40HQ containers of DN630 HDPE dredging pipe, matched pipe floats and DN630 rubber delivery hoses have been manufactured, pressure-tested and delivered to a marine contractor in Malé, Maldives. The shipment supports an island reclamation and harbour maintenance programme in the Indian Ocean, where saltwater corrosion, tidal access and limited crane capacity make lightweight HDPE the preferred pipeline material.
The complete order was loaded in 16 * 40HQ containers within 28 days of purchase order confirmation, with third-party inspection completed before vessel departure.

| Item | Specification | Quantity | Loading |
|---|---|---|---|
| HDPE dredging pipe | PE100, DN630, SDR17, 12 m segments, butt-fusion ready | 276 segments (approx. 3,312 m) | 11 * 40HQ |
| HDPE pipe floats | PU-foam filled, HDPE shell, DN630 clamp, stainless steel hardware | 260 pairs | 4 * 40HQ |
| Rubber dredge hose | DN630, steel-wire reinforced, 10 bar working pressure, flanged | 300 m (25 * 12 m) | 1 * 40HQ |
| Parameter | Value |
|---|---|
| Outside diameter | 630 mm |
| Wall thickness | 37.4 mm (SDR17) |
| Material | PE100 / PE100-RC, UV stabilised |
| Nominal pressure | 1.0 MPa (water, 20 °C) |
| Ring stiffness | SN8 (≥ 8 kN/m²) |
| Standard length | 12 m per segment |
| Jointing method | Butt fusion (hot plate) |
| Design service life | 50 years in buried and marine conditions |
DN630 refers to a nominal outside diameter of 630 mm. In dredging service this size is the standard discharge line for medium cutter suction dredgers and booster stations, balancing flow capacity against the buoyancy required from the float train.



Malé presents specific constraints that shaped the loading plan. Containers were packed in reverse installation order, so the first pipe out of the container matched the first section of the discharge line. Pipe segments were nested with timber saddles to prevent ovality during ocean transit, and float sets were shipped fully assembled to avoid on-site bolting at the quayside. Discharge at Malé commercial harbour is tide-dependent, so the delivery schedule allowed a buffer window for barge transfer to the reclamation area.

DN630 is the nominal outside diameter in millimetres. For a SDR17 pipe this corresponds to a 37.4 mm wall and a 1.0 MPa pressure rating.
Approximately 300 metres, or 25 segments of 12 m, depending on wall thickness and whether saddles or end caps are included.
Float buoyancy is calculated from the submerged weight of the pipe, the slurry inside it and the hose assembly. For DN630 SDR17, one float pair per 12 m segment is the typical configuration.
This 16-container shipment is part of an ongoing programme supplying HDPE dredging pipelines, floats and rubber hoses to island and coastal contractors across the Indian Ocean. Project-specific pipe diameters, float buoyancy and hose pressure ratings can be engineered against the dredger specification before production begins.